د کلیمبینګ فارم ورک CB240
توضیحات
Platform width: 2.4m
Roll-back system: 70 cm with carriage and rack system
Finishing platform: for removing the climbing cone, polishing concrete surface etc.
Anchor system: should be pre-fixed into the formwork and left in the concrete after pouring.
Formwork: can be moved horizontally, vertically and tilted to meet site requirement.
Main platform: provide workers a safe working platform
Finishing platform: there is an access to the main platform by using a safety ladder.
ګټې
- د ټولو ساختماني دیوال فارم ورکونو سره مطابقت لري.
- د بریکٹ او فارم ورک پینلونو څخه جوړ شوي سیټونه د یو واحد کرین لفټ سره راتلونکي ډکولو مرحلې ته لیږدول کیږي.
- د هر ډول جوړښتونو سره د تطبیق وړ، په شمول د مستقیم، متوجه او سرکلر دیوالونو په شمول.
- دا ممکنه ده چې په بیلابیلو کچو کې کاري پلیټ فارمونه جوړ کړئ. د خوندیتوب زینې لخوا چمتو شوي پلیټ فارمونو ته لاسرسی.
- په ټولو بریکٹونو کې ټول نښلونکي شامل دي چې د هینډریلونو، پش پلپرپس او نورو لوازمو فکس کولو لپاره.
- د ختلو قوسونه د یو سیسټم په کارولو سره د فارم ورک پینل بیرته راګرځولو ته اجازه ورکوي، چې د موټر او ریک لخوا جوړ شوی، په دې قوسونو کې شامل شوي.
- Formwork’s vertical adjusting and plumbing is completedwithleveling screw jacks and push-pull props.
- بریکٹونه د لنگر شنک سیسټم سره دیوال ته لنگر شوي دي.
د ختلو کړنلاره
The first pouring is to be completed by using the proper wall elements and has to be exactly د تنظیم کولو سټرټونو سره سمون لري. |
2 ګام The completely pre-assembled climbing scaffold units consisting of climbing brackets with plank bottom and bracing have to be attached to the bracket anchoring and secured. Then the formwork and the move-off carriage together with the aligning beam has to be positioned on the brackets and fixed. |
3 ګام After shifting the climbing scaffold unit to the next pouring position the finishing platform is to be mounted to the brackets to complete the climbing system. |
4 ګام Release and remove bolts that fixing the positioning anchor point. ټی راډ خلاص او لرې کړئ Loosen the wedges of the carriage unit. |
5 ګام Retract the carriage and lock it with wedge. د پورته ختلو شنک نصب کړئ د باد خوندي کولو وسیله خلاص کړئ، که کوم وي د ښکته پورته کولو شنک لرې کړئ
|
شپږم ګام Adjust the carriage into the common center of gravity and lock it again. د کرین سلینګ د عمودی والینګ سره وصل کړئ د بریکٹ امنیتي بولټونه لرې کړئ Lift the climbing bracket by crane and attach it to the next prepared climbing cone. امنیتي بولټونه بیا دننه کړئ او لاک کړئ. که اړتیا وي، د باد بارولو وسیله نصب کړئ. |
7 ګام Move the carriage back and lock it by wedge. فورمه پاکه کړئ. د تقویت بارونه نصب کړئ. |
8 ګام Move the formwork forward until lower end rests against top of the finished section of the wall فارم ورک په عمودی ډول د فشار - پل بریس په واسطه تنظیم کړئ. د دیوال فارم ورک لپاره د ټای راډونه درست کړئ |