تسلق صندقة CB240

يعتبر Climbing Formwork CB240 عبارة عن نظام تسلق يعتمد على الرافعة وهيكل دعم يستخدم على نطاق واسع لصب الجدران العالية. إنها تعمل كمنصة حاملة بالإضافة إلى منصة عمل آمنة.

اعتمادًا على طول المنصة، ينطبق نظام التسلق على ارتفاعات تزيد عن 100 متر فوق سطح الأرض ويسمح بحد أقصى لارتفاع القوالب يصل إلى 5.40 مترًا.



تفاصيل المنتج

الأوصاف

Platform width:      2.4m
Roll-back system:   70 cm with carriage and rack system
Finishing platform:  for removing the climbing cone, polishing concrete surface etc.
Anchor system:      should be pre-fixed into the formwork and left in the concrete after pouring.
Formwork:            can be moved horizontally, vertically and tilted to meet site requirement.
Main platform:       provide workers a safe working platform
Finishing platform:  there is an access to the main platform by using a safety ladder.

  • Read More About china semi automatic climbing formwork

     

  • Read More About climbing formwork for core wall

     

  • Read More About china climbing formwork system

     

  • Read More About china climbing system formwork

     

مزايا

  • متوافق مع جميع قوالب صب الخرسانة للجدران الإنشائية.
  • يتم نقل المجموعات المكونة من الأقواس وألواح القوالب إلى خطوة الصب التالية باستخدام رافعة واحدة.
  • قابلة للتكيف مع أي هياكل، بما في ذلك الجدران المستقيمة والمائلة والدائرية.
  • من الممكن بناء منصات عمل على مستويات مختلفة. ويتم توفير الوصول إلى المنصات عن طريق سلالم السلامة.
  • تشتمل جميع الأقواس على جميع الوصلات لتثبيت الدرابزين وأدوات الدفع والسحب وغيرها من الملحقات.
  • تتيح أقواس التسلق إمكانية دحرجة ألواح صب الخرسانة إلى الخلف باستخدام نظام يتكون من عربة ورف مدمجين في هذه الأقواس.
  • Formwork’s vertical adjusting and plumbing is completedwithleveling screw jacks and push-pull props.
  • يتم تثبيت الأقواس على الحائط باستخدام نظام مخروطي التثبيت.

إجراء التسلق

Read More About climbing formworkالخطوة 1

The first pouring is to be completed by using the proper wall elements and has to be exactly

تتماشى مع ضبط الدعامات.

Read More About climbing formworks

الخطوة 2

The completely pre-assembled climbing scaffold units consisting of

climbing brackets with plank bottom and bracing have to be attached to the bracket anchoring and secured.

Then the formwork and the move-off carriage together with the aligning beam has to be positioned on the brackets and fixed.

Read More About climbing formwork system

الخطوه 3

After shifting the climbing scaffold unit to the next pouring position the finishing platform is to be mounted to the brackets to complete the climbing system.

Read More About climbing system formwork

الخطوة 4

Release and remove bolts that fixing the positioning anchor point.

قم بفك وإزالة قضيب التعادل

Loosen the wedges of the carriage unit.

Read More About self climbing formwork system

الخطوة 5

Retract the carriage and lock it with wedge.

تثبيت مخاريط التسلق العلوية

قم بفك جهاز تأمين الرياح، إن وجد

قم بإزالة مخروط التسلق السفلي

 

Read More About automatic climbing formwork system

الخطوة 6

Adjust the carriage into the common center of gravity and lock it again.

نعلق حبال الرافعة إلى الجدار العمودي

قم بإزالة مسامير الأمان الخاصة بالقوس

Lift the climbing bracket by crane and attach it to the next prepared climbing cone.

أدخل مسامير الأمان وأغلقها مرة أخرى.

قم بتثبيت جهاز تحميل الرياح، إذا لزم الأمر.

Read More About auto climbing formwork system

الخطوة 7

Move the carriage back and lock it by wedge.

تنظيف القوالب.

تثبيت قضبان التسليح.

Read More About climbing formworks

الخطوة 8

Move the formwork forward until lower  end rests against top of the finished section of the wall

ضبط القوالب عموديا عن طريق دعامة الدفع والسحب.

إصلاح قضبان التعادل لقوالب صب الجدار

 

 

إذا كنت مهتمًا بمنتجاتنا، يمكنك اختيار ترك معلوماتك هنا، وسنتواصل معك قريبًا.


اكتب رسالتك هنا وأرسلها لنا

فئات المنتجات

إذا كنت مهتمًا بمنتجاتنا، يمكنك اختيار ترك معلوماتك هنا، وسنتواصل معك قريبًا.


arArabic