Piʻi Papahana CB240
Nā wehewehe
Platform width: 2.4m
Roll-back system: 70 cm with carriage and rack system
Finishing platform: for removing the climbing cone, polishing concrete surface etc.
Anchor system: should be pre-fixed into the formwork and left in the concrete after pouring.
Formwork: can be moved horizontally, vertically and tilted to meet site requirement.
Main platform: provide workers a safe working platform
Finishing platform: there is an access to the main platform by using a safety ladder.
Pono
- Kūpono me nā ʻano hana pā hale a pau o Construccion.
- ʻO nā pūʻulu i hana ʻia me nā brackets a me nā panela formwork e neʻe ʻia i ke kaʻina ninini aʻe me ka hoʻokiʻekiʻe crane hoʻokahi.
- Hiki ke hoʻololi ʻia i kēlā me kēia hale, me nā paia pololei, inclined a puni.
- Hiki ke kūkulu i nā papa hana ma nā pae like ʻole. ʻO ke komo ʻana i ka platformsis i hāʻawi ʻia e nā alapiʻi palekana.
- Loaʻa i nā brackets nā mea hoʻohui a pau e hoʻoponopono i nā lima lima, push-pullprops a me nā mea pono ʻē aʻe.
- ʻO nā pale piʻi e ʻae i ka ʻōwili ʻana i ka panel formwork me ka hoʻohana ʻana i kahi ʻōnaehana, i hana ʻia e ke kaʻa a me kahi pahu, i hoʻokomo ʻia i loko o kēia mau bracket.
- Formwork’s vertical adjusting and plumbing is completedwithleveling screw jacks and push-pull props.
- Hoʻopaʻa ʻia ʻo Bracket i ka paia me ka ʻōnaehana cone heleuma.
Kaʻina piʻi
The first pouring is to be completed by using the proper wall elements and has to be exactly aligned me ka hoʻoponopono struts. |
KaʻAnuʻu 2 The completely pre-assembled climbing scaffold units consisting of climbing brackets with plank bottom and bracing have to be attached to the bracket anchoring and secured. Then the formwork and the move-off carriage together with the aligning beam has to be positioned on the brackets and fixed. |
KaʻAnuʻu 3 After shifting the climbing scaffold unit to the next pouring position the finishing platform is to be mounted to the brackets to complete the climbing system. |
KaʻAnuʻu 4 Release and remove bolts that fixing the positioning anchor point. Wehe a wehe i ke kaulahao Loosen the wedges of the carriage unit. |
KaʻAnuʻu 5 Retract the carriage and lock it with wedge. E hoʻouka i nā cones piʻi luna Wehe i ka mea pale makani, inā he Wehe i ka piko piʻi haʻahaʻa
|
KaʻAnuʻu 6 Adjust the carriage into the common center of gravity and lock it again. E hoʻopili i ka maʻa crane i ka waling kū pololei Wehe i nā kī palekana o ka pale Lift the climbing bracket by crane and attach it to the next prepared climbing cone. E hoʻokomo a laka hou i nā kī palekana. E hoʻouka i ka mea hoʻoili makani, inā pono. |
KaʻAnuʻu 7 Move the carriage back and lock it by wedge. E hoʻomaʻemaʻe i ka puka. E hoʻouka i nā pahu hoʻoikaika. |
KaʻAnuʻu 8 Move the formwork forward until lower end rests against top of the finished section of the wall E hoʻopololei i ka formwork ma ke ʻano o ka pahu huki huki. E hoʻopaʻa i nā lāʻau hoʻopaʻa no ka pa |