කඳු නැගීමේ ආකෘති CB240
විස්තර
Platform width: 2.4m
Roll-back system: 70 cm with carriage and rack system
Finishing platform: for removing the climbing cone, polishing concrete surface etc.
Anchor system: should be pre-fixed into the formwork and left in the concrete after pouring.
Formwork: can be moved horizontally, vertically and tilted to meet site requirement.
Main platform: provide workers a safe working platform
Finishing platform: there is an access to the main platform by using a safety ladder.
වාසි
- සියලුම ඉදිකිරීම් බිත්ති ආකෘති සමග අනුකූල වේ.
- වරහන් සහ ආකෘති පුවරු වලින් සාදන ලද කට්ටල තනි දොඹකර එසවීම සමඟ ඊළඟ වත් කිරීමේ පියවර වෙත ගෙන යනු ලැබේ.
- සෘජු, ආනත සහ රවුම් බිත්ති ඇතුළුව ඕනෑම ව්යුහයකට අනුවර්තනය විය හැකිය.
- විවිධ මට්ටම්වල වැඩ කරන වේදිකා ගොඩනගා ගත හැකිය. ආරක්ෂිත ඉණිමඟ මගින් සපයනු ලබන වේදිකාවට ප්රවේශය.
- සියලුම වරහන් වල අත් පටි, තල්ලු-පුල්ප්රොප් සහ අනෙකුත් උපාංග සවි කිරීම සඳහා සියලුම සම්බන්ධක ඇතුළත් වේ.
- කඳු නැගීමේ වරහන් මඟින් මෙම වරහන් තුළ ඇතුළත් කර ඇති කරත්තයක් සහ රාක්කයක් මඟින් සාදන ලද පද්ධතියක් භාවිතයෙන් ආකෘති පුවරුව පෙරළීමට ඉඩ සලසයි.
- Formwork’s vertical adjusting and plumbing is completedwithleveling screw jacks and push-pull props.
- වරහන් නැංගුරම් කේතු පද්ධතියක් සමඟ බිත්තියට නැංගුරම් ලා ඇත.
කඳු නැගීමේ ක්රියා පටිපාටිය
The first pouring is to be completed by using the proper wall elements and has to be exactly ගැලපුම් නූල් සමග පෙලගැසී ඇත. |
පියවර 2 The completely pre-assembled climbing scaffold units consisting of climbing brackets with plank bottom and bracing have to be attached to the bracket anchoring and secured. Then the formwork and the move-off carriage together with the aligning beam has to be positioned on the brackets and fixed. |
පියවර 3 After shifting the climbing scaffold unit to the next pouring position the finishing platform is to be mounted to the brackets to complete the climbing system. |
පියවර 4 Release and remove bolts that fixing the positioning anchor point. ටයි පටිය ලිහිල් කර ඉවත් කරන්න Loosen the wedges of the carriage unit. |
පියවර 5 Retract the carriage and lock it with wedge. ඉහළ කඳු නැගීමේ කේතු සවි කරන්න සුළං ආරක්ෂිත උපාංගයක් තිබේ නම් ලිහිල් කරන්න පහළ කඳු නැගීමේ කේතුව ඉවත් කරන්න
|
පියවර 6 Adjust the carriage into the common center of gravity and lock it again. දොඹකරය සිරස් අතට සවි කරන්න වරහනේ ආරක්ෂක බෝල්ට් ඉවත් කරන්න Lift the climbing bracket by crane and attach it to the next prepared climbing cone. ආරක්ෂක බෝල්ට් නැවත ඇතුල් කර අගුළු දමන්න. අවශ්ය නම්, සුළං පැටවීමේ උපකරණය ස්ථාපනය කරන්න. |
පියවර 7 Move the carriage back and lock it by wedge. ආකෘති පත්රය පිරිසිදු කරන්න. ශක්තිමත් කිරීමේ තීරු සවි කරන්න. |
පියවර 8 Move the formwork forward until lower end rests against top of the finished section of the wall තල්ලු-අදින්න වරහන මගින් ආකෘති පත්රය සිරස් අතට සකසන්න. බිත්ති ආකෘතිය සඳහා ටයි පොලු සවි කරන්න |